Supported Device Types

This is the current list of supported device types that work with this plugin. Each type corresponds to a value you set in the type field of your device configuration.

If you are looking for verified configurations for your specific device, see the Configuration Examples.

Device Type Reference

Device	Type	Notes
Air Conditioner	`AirConditioner`	Cooling and heating devices (details)
Air Purifier	`AirPurifier`	Purifiers with fan speed control (details)
Circuit Breaker Monitor	`CircuitBreakerMonitor`	Read-only energy and safety monitoring (details)
Heat Convector	`Convector`	Heating panels (details)
Non-sequential Power Strip	`CustomMultiOutlet`	Power strips with non-sequential data-points per outlet (details)
Dehumidifier	`Dehumidifier`	Humidity control with fan speed (details)
Smart Fan Regulator	`Fan`	Fan regulators with controllable speeds (details)
Smart Fan with Light	`FanLight`	Fan with speeds, direction, and built-in light (details)
Garage Door	`GarageDoor`	Smart garage doors or garage door openers (details)
Mapped Heat Pump Heater	`MappedHeatPumpHeater`	Heat pump with room-to-water temp mapping (details)
Smart Power Strip	`MultiOutlet`	Power strips with sequential data-points for individual outlet control (details)
Oil Diffuser	`OilDiffuser`	Essential oil diffuser with humidifier and RGB light (details)
Smart Plug	`Outlet`	Smart plugs that turn on and off (details)
Smart Plug w/ White and Color Lights	`RGBTWOutlet`	Smart plugs with controllable RGBTW LEDs (details)
White and Color Light Bulb	`RGBTWLight`	Colored bulbs with tunable white and dimming (details)
Simple Blinds	`SimpleBlinds`	Smart blinds and smart switches that control blinds (details)
Simple Dimmer	`SimpleDimmer`	Dimmer switches with power control (details)
Simple Dimmer 2	`SimpleDimmer2`	Alternative dimmer (DP 3 brightness) (details)
Simple Heater	`SimpleHeater`	Heating solutions with only temperature control (details)
Simple Light Bulb	`SimpleLight`	Light bulbs that just turn on and off
Multi-Switch	`Switch`	Multi-switch with debounced power (details)
Tunable White Light Bulb	`TWLight`	Bulbs with tunable white and dimming functionality (details)
Water Valve	`WaterValve`	Smart valves with timer support (details)

TIP

The type value is case-insensitive. "SimpleLight", "simplelight", and "SIMPLELIGHT" all work.

Device Configuration Details

Outlets

These are plugs with a single outlet that can only be turned on or off.

json5

{
  name: 'My Outlet',
  type: 'Outlet',
  manufacturer: 'EZH',
  model: 'Wifi Mini Smart Life Outlet',
  id: '032000123456789abcde',
  key: '0123456789abcdef',

  /* If your device provides energy parameters, define these */

  /* Datapoint identifier for voltage reporting */
  voltsId: 9,

  /* Datapoint identifier for amperage reporting */
  ampsId: 8,

  /* Datapoint identifier for wattage reporting */
  wattsId: 7,

  /* Often voltage is reported divided by 10; if that is
     not the case for you, override the default */
  voltsDivisor: 10,

  /* Often amperage is reported divided by 1000; if that is
     not the case for you, override the default */
  ampsDivisor: 1000,

  /* Often wattage is reported divided by 10; if that is
     not the case for you, override the default */
  wattsDivisor: 10,

  /* Additional parameters to override defaults only if needed */

  /* Override the default datapoint identifier for power */
  dpPower: 1,
}

Tunable White Light Bulbs

These are light bulbs that let you control the brightness and tune the bulb's light from warm white to daylight white.

json5

{
  name: 'My Tunable White Bulb',
  type: 'TWLight',
  manufacturer: 'Iotton',
  model: 'Smart White Bulb',
  id: '032000123456789abcde',
  key: '0123456789abcdef',

  /* Additional parameters to override defaults only if needed */

  /* Override the default datapoint identifier for power */
  dpPower: 1,

  /* Override the default datapoint identifier for brightness */
  dpBrightness: 2,

  /* Override the default datapoint identifier for color-temperature */
  dpColorTemperature: 3,

  /* Minimum white temperature mired value
     (See https://en.wikipedia.org/wiki/Mired) */
  minWhiteColor: 140,

  /* Maximum white temperature mired value */
  maxWhiteColor: 400,
}

White and Color Light Bulbs

These are bulbs that can produce white light as well as colors and allow you to control the brightness. They also let you tune the color-temperature of the white light.

There are two kinds of color devices:

The most common ones use 14 characters to represent the color (HEXHSB).
Others use 12 characters for the color (HSB).

The colorFunction defaults to HEXHSB but can be overridden in the config block to use the second type.

It is common for HEXHSB devices to use white color temperature and brightness values from 0 to 255 (scale of 255). It is also common for HSB devices to use values from 0 to 1000 (scale of 1000). If a device doesn't follow these common values, scaleWhiteColor and scaleBrightness can help.

json5

{
  name: 'My Colored Bulb',
  type: 'RGBTWLight',
  manufacturer: 'Novostella',
  model: 'Color Changing Floor Light',
  id: '032000123456789abcde',
  key: '0123456789abcdef',

  /* Additional parameters to override defaults only if needed */

  /* Override the default datapoint identifier for power */
  dpPower: 1,

  /* Override the default datapoint identifier for mode (white vs color) */
  dpMode: 2,

  /* Override the default datapoint identifier for brightness */
  dpBrightness: 3,

  /* Override the default datapoint identifier for color-temperature of the whites */
  dpColorTemperature: 4,

  /* Override the default datapoint identifier for color */
  dpColor: 5,

  /* Minimum white temperature mired value
     (See https://en.wikipedia.org/wiki/Mired) */
  minWhiteColor: 140,

  /* Maximum white temperature mired value */
  maxWhiteColor: 400,

  /* Override the color format (default: HEXHSB)
     Only use if your device is not recognized correctly
     Using HSB defaults the scale of brightness and white color to 1000 */
  colorFunction: 'HEXHSB',

  /* Override the default brightness scale */
  scaleBrightness: 255,

  /* Override the default color temperature scale */
  scaleWhiteColor: 255,
}

Smart Power Strips

These devices can have any number of controllable outlets. To let the plugin know how many your device supports, add an additional parameter named outletCount.

json5

{
  name: 'My Power Strip',
  type: 'MultiOutlet',
  manufacturer: 'GeekBee',
  model: 'Smart Wifi Power Strip',
  id: '032000123456789abcde',
  key: '0123456789abcdef',

  /* This device has 3 outlets and 2 USB ports, all individually controllable */
  outletCount: 5,
}

Non-sequential Power Strips

Some smart power strips don't have sequential data-points. Using CustomMultiOutlet you can define the data-points explicitly.

json5

{
  name: 'My Power Strip',
  type: 'CustomMultiOutlet',
  manufacturer: 'GeekBee',
  model: 'Smart Wifi Power Strip',
  id: '032000123456789abcde',
  key: '0123456789abcdef',

  /* Define your data-points here; add more as needed */
  outlets: [
    {
      name: 'Outlet 1',
      dp: 1,
    },
    {
      name: 'Outlet 2',
      dp: 2,
    },
    {
      name: 'USB 1',
      dp: 7,
    },
  ],
}

Air Conditioners

These devices have cooling and/or heating capabilities; they could also have dry, fan, or other modes but HomeKit's definition doesn't facilitate modes other than heat, cool, and auto.

By default, heat and cool modes are enabled. To disable one, set noHeat or noCool to true.

Tuya devices don't follow a unified pattern for naming the modes — for example, cooling mode is called COOL on Kogan's KAPRA14WFGA and cold on Igenix's IG9901WIFI. By default the plugin uses COOL and HEAT; override with cmdCool and cmdHeat as needed.

json5

{
  name: 'My Air Conditioner',
  type: 'AirConditioner',
  manufacturer: 'Kogan',
  model: 'KAPRA14WFGA',
  id: '032000123456789abcde',
  key: '0123456789abcdef',

  /* Additional parameters to override defaults only if needed */

  /* This device has no cooling function */
  noCool: true,

  /* This device has no heating function */
  noHeat: true,

  /* Override cooling phrase */
  cmdCool: 'COOL',

  /* Override heating phrase */
  cmdHeat: 'HEAT',

  /* This device has no oscillation (swinging) function */
  noSwing: true,

  /* Minimum temperature supported, in Celsius (°C) */
  minTemperature: 15,

  /* Maximum temperature supported, in Celsius (°C) */
  maxTemperature: 40,

  /* Temperature change steps, in Celsius (°C) */
  minTemperatureSteps: 1,
}

Heat Convectors

Heating panels with a low or high setting. Since HomeKit doesn't accommodate that directly, it is mapped to Fan Speed — be aware that when the fan speed slider is at the lowest value, it turns the device off.

By default the plugin uses LOW and HIGH to request these settings; override with cmdLow and cmdHigh if your device uses different casing or phrases (e.g., Low and High).

If your signature doesn't have a variation of low or high, SimpleHeater would be the correct device type to use instead.

json5

{
  name: 'My Heat Convector',
  type: 'Convector',
  manufacturer: 'Gorenje',
  model: 'OptiHeat 2000 EWP',
  id: '032000123456789abcde',
  key: '0123456789abcdef',

  /* Additional parameters to override defaults only if needed */

  /* Override the default datapoint identifier of activity */
  dpActive: 7,

  /* Override the default datapoint identifier for the desired temperature */
  dpDesiredTemperature: 2,

  /* Override the default datapoint identifier for the current temperature */
  dpCurrentTemperature: 3,

  /* Override the default datapoint identifier for rotation speed */
  dpRotationSpeed: 4,

  /* Override the default datapoint identifier for child-lock */
  dpChildLock: 6,

  /* Override the default datapoint identifier for temperature-display units */
  dpTemperatureDisplayUnits: 19,

  /* Override phrase for low setting */
  cmdLow: 'Low',

  /* Override phrase for high setting */
  cmdHigh: 'High',

  /* This device does not provide locking the physical controls */
  noChildLock: true,

  /* This device has no function to change the temperature units */
  noTemperatureUnit: true,

  /* Minimum temperature supported, in Celsius (°C) */
  minTemperature: 15,

  /* Maximum temperature supported, in Celsius (°C) */
  maxTemperature: 35,
}

Simple Dimmers

Switches that allow turning on/off and dimming.

json5

{
  name: 'My Simple Dimmer',
  type: 'SimpleDimmer',
  manufacturer: 'TESSAN',
  model: 'Smart Dimmer Switch',
  id: '032000123456789abcde',
  key: '0123456789abcdef',

  /* Additional parameters to override defaults only if needed */

  /* Override the default datapoint identifier for power */
  dpPower: 1,

  /* Override the default datapoint identifier for brightness */
  dpBrightness: 2,

  /* Override the default brightness scale. Common values are 255 or 1000 */
  scaleBrightness: 1000,
}

Simple Heaters

While defined mainly to develop a more robust device type, this can be used to control a heating device by only setting a desired temperature.

json5

{
  name: 'My Simple Heater',
  type: 'SimpleHeater',
  manufacturer: 'Branded',
  model: 'Simple',
  id: '032000123456789abcde',
  key: '0123456789abcdef',

  /* Additional parameters to override defaults only if needed */

  /* Override the default datapoint identifier for being active */
  dpActive: 1,

  /* Override the default datapoint identifier for the desired temperature */
  dpDesiredTemperature: 2,

  /* Override the default datapoint identifier for the current temperature */
  dpCurrentTemperature: 3,

  /* If your device reports temperatures in multiples of the real value, define it here.
     e.g., if your device reports 155 for 15.5°C, use the value 10 */
  temperatureDivisor: 1,

  /* Minimum temperature supported, in Celsius (°C) */
  minTemperature: 15,

  /* Maximum temperature supported, in Celsius (°C) */
  maxTemperature: 35,
}

Garage Doors

Early Testing

If your garage door or garage door opener does more than just open and close (e.g., reports its position or detects obstacles), please create an issue and paste your signature with any information you can provide.

json5

{
  name: 'My Garage Door',
  type: 'GarageDoor',
  manufacturer: 'eWeLink',
  model: 'WiFi Switch Garage Door Controller',
  id: '032000123456789abcde',
  key: '0123456789abcdef',

  /* Additional parameters to override defaults only if needed */

  /* Override the default datapoint identifier for triggering the opener */
  dpAction: 1,

  /* Override the default datapoint identifier for the state of the door */
  dpStatus: 2,

  /* If the app reports open when the door is closed,
     and reports closed when it is open */
  flipState: true,
}

Simple Blinds

Normally blinds don't report their position. This plugin attempts to time the movements to estimate the positions. You can adjust a few parameters to make it accurate for your setup.

json5

{
  name: 'My Simple Blinds',
  type: 'SimpleBlinds',
  manufacturer: 'TeePao',
  model: 'Roller Switch',
  id: '032000123456789abcde',
  key: '0123456789abcdef',

  /* Additional parameters to override defaults only if needed */

  /* How many seconds does it take to fully open from a fully closed state */
  timeToOpen: 45,

  /* How many seconds it spends tightening the blinds while closing */
  timeToTighten: 0,

  /* If the app reports open when the blinds are closed,
     and reports closed when they are open */
  flipState: true,
}

Outlets with White and Color Lights

These are plugs with a single outlet that have controllable white and colored LEDs on them.

There are two kinds of color devices:

The most common ones use 14 characters to represent the color (HEXHSB).
Others use 12 characters for the color (HSB).

The colorFunction defaults to HEXHSB but can be overridden in the config block to use the second type.

json5

{
  name: 'My Colored Outlet',
  type: 'RGBTWOutlet',
  manufacturer: 'EZH',
  model: 'Wifi Colored Smart Life Outlet',
  id: '032000123456789abcde',
  key: '0123456789abcdef',

  /* If your device provides energy parameters, define these */

  /* Datapoint identifier for voltage reporting */
  voltsId: 9,

  /* Datapoint identifier for amperage reporting */
  ampsId: 8,

  /* Datapoint identifier for wattage reporting */
  wattsId: 7,

  /* Often voltage is reported divided by 10; if that is
     not the case for you, override the default */
  voltsDivisor: 10,

  /* Often amperage is reported divided by 1000; if that is
     not the case for you, override the default */
  ampsDivisor: 1000,

  /* Often wattage is reported divided by 10; if that is
     not the case for you, override the default */
  wattsDivisor: 10,

  /* Additional parameters to override defaults only if needed */

  /* Override the default datapoint identifier for outlet power */
  dpPower: 101,

  /* Override the default datapoint identifier for light power */
  dpLight: 1,

  /* Override the default datapoint identifier for mode (white vs color) */
  dpMode: 2,

  /* Override the default datapoint identifier for brightness */
  dpBrightness: 3,

  /* Override the default datapoint identifier for color-temperature of the whites */
  dpColorTemperature: 4,

  /* Override the default datapoint identifier for color */
  dpColor: 5,

  /* Minimum white temperature mired value
     (See https://en.wikipedia.org/wiki/Mired) */
  minWhiteColor: 140,

  /* Maximum white temperature mired value */
  maxWhiteColor: 400,

  /* Override the color format (default: HEXHSB)
     Only use if your device is not recognized correctly
     Using HSB defaults the scale of brightness and white color to 1000 */
  colorFunction: 'HEXHSB',

  /* Override the default brightness scale */
  scaleBrightness: 255,

  /* Override the default color temperature scale */
  scaleWhiteColor: 255,
}

Smart Fan Regulators

These are accessories that act as a regulator switch or an inbuilt regulator for your ceiling fan. Most common options are an on/off switch and speed controls generally controlled through two buttons — one speed at a time in each direction.

There are two kinds of regulator devices:

The most common ones use 3 speed controls.
Others use 5 speed controls, found compatible with most fan regulators in India, Australia, and the UK.

json5

{
  name: 'My Fan',
  type: 'Fan',
  manufacturer: 'HomeMate',
  model: 'HomeMate 5-Speed Smart Touch-Controlled Fan Regulator',
  id: '032000123456789abcde',
  key: '0123456789abcdef',

  /* Override the default datapoint identifier of activity */
  dpActive: '1',

  /* Override the default datapoint identifier of rotation speed */
  dpRotationSpeed: '2',
}

Smart Fan with Light

These are fan devices with controllable speeds, direction, and a built-in light. There are multiple kinds of devices with different speed and light controls.

json5

{
  type: 'FanLight',
  name: 'My Fan with Light',
  id: '032000123456789abcde',
  key: '0123456789abcdef',
  manufacturer: 'Hunter Pacific International',
  model: 'Polar v2 Fan',

  dpLight: 20,
  useBrightness: true,
  dpBrightness: 22,
  minBrightness: 1,
  scaleBrightness: 9,

  dpActive: 60,
  dpRotationSpeed: 62,
  maxSpeed: 9,
  dpRotationDirection: 63,
}

Air Purifiers

Air purifiers with fan speed control. Supports manufacturers like Breville, Proscenic, and Siguro with different speed configurations.

json5

{
  name: 'My Air Purifier',
  type: 'AirPurifier',
  manufacturer: 'Breville',
  model: 'Smart Air Purifier',
  id: '032000123456789abcde',
  key: '0123456789abcdef',

  /* Additional parameters to override defaults only if needed */

  /* Override the default phrase for auto mode (default: 'AUTO') */
  cmdAuto: 'AUTO',

  /* Disable rotation speed control if your device uses preset modes */
  noRotationSpeed: true,

  /* Number of fan speed steps (only when noRotationSpeed is true) */
  fanSpeedSteps: 3,

  /* Display air quality sensor in HomeKit */
  showAirQuality: true,

  /* Custom name for air quality sensor */
  nameAirQuality: 'Air Quality',
}

Dehumidifiers

Dehumidifiers with target humidity control, fan speed adjustment, and optional child lock.

json5

{
  name: 'My Dehumidifier',
  type: 'Dehumidifier',
  manufacturer: 'Pro Breeze',
  model: 'Smart Dehumidifier',
  id: '032000123456789abcde',
  key: '0123456789abcdef',

  /* Additional parameters to override defaults only if needed */

  /* Override the default datapoint identifiers */
  dpActive: '1',
  dpMode: '2',
  dpTargetHumidity: '4',
  dpFanSpeed: '6',
  dpChildLock: '7',
  dpCurrentTemperature: '103',
  dpCurrentHumidity: '104',

  /* Disable child lock service */
  noChildLock: true,

  /* Disable fan speed control service */
  noSpeed: true,

  /* Fan speed range (default: 1-2) */
  minSpeed: 1,
  maxSpeed: 3,
  speedSteps: 1,
}

Circuit Breaker Monitors

Safety-critical read-only device for monitoring digital circuit breakers. Exposes temperature, leakage current detection, fault alarms, and energy consumption to HomeKit.

Read-Only Safety Device

The breaker switch (DP 16) is never exposed to HomeKit for safety reasons. This device is for monitoring only.

json5

{
  name: 'Main Panel Monitor',
  type: 'CircuitBreakerMonitor',
  manufacturer: 'Tuya',
  model: 'Digital Circuit Breaker',
  id: '032000123456789abcde',
  key: '0123456789abcdef',

  /* Additional parameters to override defaults only if needed */

  /* Override the default datapoint identifiers */
  dpTemperature: '103',
  dpLeakageCurrent: '15',
  dpFault: '9',
  dpTotalForwardEnergy: '1',
  dpPhaseA: '6',
  dpSwitch: '16',

  /* Temperature divisor (device reports temp * divisor) */
  temperatureDivisor: 1,

  /* Energy divisor (device reports kWh * divisor) */
  energyDivisor: 100,

  /* Leakage current threshold in mA for alarm (default: 30) */
  leakageThreshold: 30,

  /* Disable specific sensors */
  exposeTemperatureSensor: false,
  exposeLeakSensor: false,
  exposeFaultSensor: false,

  /* Disable energy characteristic (KilowattHours) */
  exposeEnergyCharacteristic: false,

  /* Custom sensor names */
  leakSensorName: 'Panel Leakage',
  faultSensorName: 'Panel Fault',
}

Exposed HomeKit Services:

TemperatureSensor — Device temperature with optional KilowattHours energy characteristic
LeakSensor — Leakage current alarm (triggers when current ≥ threshold)
ContactSensor — Fault alarm (Closed = no fault, Open = fault detected)

Mapped Heat Pump Heaters

Heat pump heaters with virtual room-to-water temperature mapping. Displays tank/return temperature as current temperature and maps a virtual room target to actual water setpoint using an interpolation table.

json5

{
  name: 'Heat Pump',
  type: 'MappedHeatPumpHeater',
  manufacturer: 'Ferroli',
  model: 'Omnia S 3.2',
  id: '032000123456789abcde',
  key: '0123456789abcdef',

  /* Additional parameters to override defaults only if needed */

  /* Override the default datapoint identifiers */
  dpActive: '1',
  dpReturnTemperature: '25',
  dpWaterTarget: '117',
  dpOutsideTemperature: '118',
  dpFlowTemperature: '119',

  /* Temperature divisors (device reports temp * divisor) */
  returnTemperatureDivisor: 10,
  waterTargetDivisor: 1,
  outsideTemperatureDivisor: 10,
  flowTemperatureDivisor: 10,

  /* Virtual room temperature range (°C) */
  roomTargetMin: 18,
  roomTargetMax: 24,
  defaultRoomTarget: 20,
  minTemperatureSteps: 0.5,

  /* Actual water temperature range (°C) */
  waterTargetMin: 35,
  waterTargetMax: 55,

  /* Room-to-water temperature mapping table */
  roomToWaterMap: [
    { room: 18, water: 35 },
    { room: 20, water: 40 },
    { room: 22, water: 47 },
    { room: 24, water: 55 },
  ],

  /* Expose optional temperature sensors */
  exposeOutsideSensor: true,
  outsideSensorName: 'Heat Pump Outside',
  exposeFlowSensor: true,
  flowSensorName: 'Heat Pump Flow',
  exposeReturnSensor: true,
  returnSensorName: 'Heat Pump Return',
}

Multi-Switch Accessories

Multi-switch accessories with debounced power switching to prevent rapid on/off cycles.

json5

{
  name: 'My Switch',
  type: 'Switch',
  manufacturer: 'Treatlife',
  model: '3-Gang Smart Switch',
  id: '032000123456789abcde',
  key: '0123456789abcdef',

  /* Number of switches (default: 1) */
  switchCount: 3,
}

Notes:

Each switch appears as a separate accessory in HomeKit labeled {name} 1, {name} 2, etc.
Switch commands are debounced by 500ms to prevent rapid toggling issues.

Water Valves

Smart valves with timer support for irrigation, shower heads, or faucets.

json5

{
  name: 'Garden Valve',
  type: 'WaterValve',
  manufacturer: 'Smart Home',
  model: 'WiFi Water Valve',
  id: '032000123456789abcde',
  key: '0123456789abcdef',

  /* Additional parameters to override defaults only if needed */

  /* Override the default datapoint identifier for power */
  dpPower: '1',

  /* Valve type: GENERIC (0), IRRIGATION (1), SHOWER_HEAD (2), WATER_FAUCET (3) */
  valveType: 'IRRIGATION',

  /* Default duration in seconds (default: 600) */
  defaultDuration: 1800,

  /* Disable timer functionality */
  noTimer: true,
}

Oil Diffusers

Essential oil diffusers combining humidifier and RGB light functionality.

json5

{
  name: 'My Diffuser',
  type: 'OilDiffuser',
  manufacturer: 'Asakuki',
  model: 'Essential Oil Diffuser',
  id: '032000123456789abcde',
  key: '0123456789abcdef',

  /* Additional parameters to override defaults only if needed */

  /* Override the default datapoint identifiers */
  dpActive: '1',
  dpRotationSpeed: '2',
  dpLight: '5',
  dpMode: '6',
  dpColor: '8',
  dpWaterLevel: '9',

  /* Maximum mist intensity level */
  maxSpeed: 2,

  /* Flip speed slider (reverse min/max) */
  enableFlipSpeedSlider: true,
}

Exposed HomeKit Services:

HumidifierDehumidifier — Mist output control
Lightbulb — RGB color control with hue/saturation

Simple Dimmer 2

Alternative dimmer implementation using DP 3 for brightness. Use this if SimpleDimmer doesn't work for your device.

json5

{
  name: 'My Dimmer',
  type: 'SimpleDimmer2',
  manufacturer: 'Smart Home',
  model: 'Wall Dimmer Switch',
  id: '032000123456789abcde',
  key: '0123456789abcdef',

  /* Additional parameters to override defaults only if needed */

  /* Override the default datapoint identifier for power */
  dpPower: '1',

  /* Brightness is always DP 3 for this device type */
}

Supported Device Types ​

Device Type Reference ​

Device Configuration Details ​

Outlets ​

Tunable White Light Bulbs ​

White and Color Light Bulbs ​

Smart Power Strips ​

Non-sequential Power Strips ​

Air Conditioners ​

Heat Convectors ​

Simple Dimmers ​

Simple Heaters ​

Garage Doors ​

Simple Blinds ​

Outlets with White and Color Lights ​

Smart Fan Regulators ​

Smart Fan with Light ​

Air Purifiers ​

Dehumidifiers ​

Circuit Breaker Monitors ​

Mapped Heat Pump Heaters ​

Multi-Switch Accessories ​

Water Valves ​

Oil Diffusers ​

Simple Dimmer 2 ​

Supported Device Types

Device Type Reference

Device Configuration Details

Outlets

Tunable White Light Bulbs

White and Color Light Bulbs

Smart Power Strips

Non-sequential Power Strips

Air Conditioners

Heat Convectors

Simple Dimmers

Simple Heaters

Garage Doors

Simple Blinds

Outlets with White and Color Lights

Smart Fan Regulators

Smart Fan with Light

Air Purifiers

Dehumidifiers

Circuit Breaker Monitors

Mapped Heat Pump Heaters

Multi-Switch Accessories

Water Valves

Oil Diffusers

Simple Dimmer 2